Innovative technology for safety, quality and productivity

Radiographic Testing (RT)/X-ray Inspectionfalls under the umbrella ofnon-destructive testing (NDT)and is a method that examines the target sample by penetrating it with X-rays and in so doing highlights deviations in material density that can signal an imperfection that needs to be addressed.

Radiographyuses X-rays and gamma-raysto produce a radiographic image of the target sample, allowing the technician to observe any changes in material thickness, internal and surface defects, and even assembly details (i.e. welds, joints, connectors) to ensure the highest levels of quality and safety in your production.

One of the key benefits ofRadiographic Testing (RT)is that it generates a permanent, hard-copy (in the example of x-ray film) record of the scan for a given target sample. In the example of a digital sensor/detector, the record is a digital one that can be stored locally or remotely and does not require the processing and storage needs associated with x-ray films.

What are X-rays?

x rays are ahighly-energetic form of electromagnetic radiationwith a wavelength in the range of 1nm to 1 pms, approximately 1000 to 1,000,000 times smaller than the wavelength of light. Due to their being highly energetic,x rays are able to pass through materials that absorb ordinary visible light.

In general, X-ray inspection systems consist of a radiation safe enclosure, the radiation protection cabinet, containing, in linear alignment, the X-ray tube, and the X-ray detector. A remotely controllable manipulating unitallows the user to position the sample within the beam. The final X-ray image is displayed on a monitor for computerized image processing. In addition, the X-ray system may be outfitted with an electronic program control allowing automated sample inspection.x射线图像显示对象特性s based on differences in material density.

巴勒斯坦权力机构rt of the X-ray spectrum is absorbed when passing through an object.The thicker or higher in density the object, the more X-rays are absorbed and do not pass through.Those X-rays that pass through the object strike a detector where an X-ray image is created.This image is made up of different shades of gray depending upon the intensity of the incident rays: Parts of the object that are thicker or materials that are higher in density, such as iron, copper, and lead, appear darker than less dense materials such as plastics, paper, or even air.

Thisfilm is then processed in a darkroom- much like typical photographic film - and the various degrees of radiation captured by the film are represented as different values of white and black.x rays not absorbed by the target sample will cause exposure of the radiographic detector. These areas will appear dark. Areasthat absorbed higher levels due to higher absorbing or more dense materialwill appear light.

In this way, regions of your target sample where uniform density has been changed by imperfections, such as porosity, cracks, or misalignment will appear as dark lines, thusmaking it easier for a skilled technician to detect.

Radiographic Testing (RT)is primarily used in thetesting and grading of weldson piping, pressure vessels, storage containers, pipelines, and structural welds.

Reallyanything that is joined together with a weld that is expected to bear some sort of pressure or loadis subject to radiographic testing to ensure the integrity of the welds.

Other tested objects includemachined parts, plate metal, or pipe walls(especially where corrosion is a concern).

Ceramics,light metal castings, or additive parts suchas those used in theaerospace and automotive industriesare also tested via radiography.

Radiographic Testing (RT)can be achieved viax raysorgamma rays. X-rays are produced via an X-ray tube, while gamma rays are produced by the introduction of a radioactive isotope.

These radiation sourcesuse much higher energy levels than those associated with electromagnetic waves.

Because of the ionizing radiation involved in radiography testing, it isimportant to make sure proper safety guidelines are communicated and adhered to so as to prevent exposure.

Radiographic Testing (RT)offersseveral benefits over other forms of NDT.Some of those benefits are:

• arecord of the scanthat can live either on film or digitally
• ability tolook through the whole sample
• ahigher level of identificationof a defect
• alower level of skill is required of operators and inspectors

A well-trained radiographer can not onlyaccurately locate a defectwith RT, but canalso identify its type, size, and location.

When it comes to disadvantages, the obvious is the fact thatyou are dealing with relatively dangerous materialsthat can cause adverse, long-term health effects when exposed to radiation.

Additionally, traditional RT solutions, especially film-based ones, requirea significant amount of time before one can generate a usable image, thus elongating your production cycle.

This is one reason why so many organizations today areembracing digital detectors which sidestep the processing time associated with traditional x-ray film.

X-Ray Generators

x ray generatorsproduce X-rays via electron emissionin a vacuum. After hitting a target material,x rays are emitted and directed towards your target sample. In the sample, the x-rays are absorbed or scattered according to the target's material and density. After having passed through your target sample,the photons are then captured by a detector, such as x-ray film or a digital detector.

Digital Conversion

Many organizations today aremoving away from traditional film-based radiography to a digital sensor-based solutionin an effort to save time, reduce costs, and improve overall NDT performance.

Ultrasonic Testing (UT)andEddy Current Testing (ECT)are two leading methods of NDT today due to enhanced signal quality, flexible probing options, and the fact they do not involve radiation or dangerous chemicals.

UT relies onultrasonic waves to probe through your target sampleand detect any deviations therein, while with ECT, anelectron current runs through your target samplethus generating magnetic fields which highlight material density and thickness deviations.

Both, ECT and UT (and particularly phased array ultrasonic testing) aremuch safer than RT, and in certain applications can be less time-consuming.

Portabilityis also a hallmark of ECT and UT solutions as they tend to be smaller and easier to operate, thus lending themselves towards use in the field whereas RT is geared more towards laboratory or production line applications. That being said,there are several portable RT solutions todaythat can be deployed into the field with success.

Computed tomographyprovides a three-dimensional, spatial imageof the object under inspection which can be virtually sliced in any direction. The CT-image shows different materials or density deviations (e.g. porosity) as不同深浅的灰色(或不同的颜色)。

To generate a three-dimensional image, a large number of two-dimensional X-ray images (or slices) are taken around a single axis of rotation (360 °). These X-ray images are thenreconstructed as volumetric representations of structures (3D)using a complex reconstruction algorithm.